Page 5 of 6

Re: HC Tidy Up (MOT Passed!)

PostPosted: Sat Aug 25, 2018 2:56 pm
by Kraken
Well Beigey was treated to a wash (first of the year?), a T-Cut to the top half, and a spray of Greased Lightning. Don't think I've ever spent as long cleaning a car as I did that day...

Looks the best it ever has in my possession.



Now sporting a pair of Alleycats on the front as two of the Compomotives were the wrong PCD.

I've done a couple of 25 mile journeys with no running problems. Did I fix something? I can't remember?? :oops:

Re: HC Tidy Up (MOT Passed!)

PostPosted: Sun Aug 26, 2018 6:08 am
by lord13
Looking really good, I love the simplicity of it, very clean with a nice stance :)

Re: HC Tidy Up (MOT Passed!)

PostPosted: Sun Sep 16, 2018 10:33 pm
by Kraken
I went out to a local show today. On my way there I caught up with a pair of Chevettes, a blue one and a green one - both owned by the same person. A mile away from the show the green Chevette broke down and had to be abandoned. A real shame, it would have been nice to have arrived in a Vauxhall convoy. Beigey and the blue Chevette were the only two Vauxhalls at the show. There were two Opels though, a Kadett B, and a Commodore A coupe (both absolutely lovely).

I didn't even have any tools to help with the Chevette, as I now have that much confidence in Beigey 8)



I then returned home and replaced my clutch fork spring, and swapped out my old split engine mounts for new ones - thanks Fred!

Re: HC Tidy Up (MOT Passed!)

PostPosted: Mon Jul 22, 2019 11:10 pm
by Kraken
Went to New Deer show yesterday.
Came away with 2nd place! :shock:

Image

Re: HC Tidy Up (MOT Passed!)

PostPosted: Tue Jul 23, 2019 8:15 am
by 1972nail
Well done. Great to get recognition for all your hard work. :hourra:

Re: HC Tidy Up (MOT Passed!)

PostPosted: Fri Jul 26, 2019 10:08 pm
by Kraken
Thanks.

I thought I’d finally got all running problems sorted but now I’m not so sure... drove 35 miles trouble free, stopped for half an hour, drove another 10 miles and then had it idling for a couple of minutes... then it conked out and wouldn’t start again. Checked and there was no fuel in the fuel filter.. Turning the car over the filter would fill up but the car wouldn’t start. When I stopped turning it over the fuel filter emptied almost immediately.

Half an hour later it started and ran no problem.

I was thinking maybe the fuel tank vent is partially blocked, the tank is building up a vacuum and pulling the petrol back to it? But I’m not sure, seems strange that it only conked out when it was idling?

Re: HC Tidy Up (MOT Passed!)

PostPosted: Fri Jul 26, 2019 10:25 pm
by 1972nail
It is hot outside at the minute, so could it be vaporisation? Also, all the hose clips will have expanded a bit and loosened off, this may cause an air leak which will cause any suction the pump has created to drop when the engine is switched off and fuel will drop back down the pipe. I would check that the hose clips are tight.

To check if the breather is blocked take off the filler cap, that will release any vacuum if there is any.

Re: HC Tidy Up (MOT Passed!)

PostPosted: Sat Aug 03, 2019 2:46 pm
by Kraken
I forgot to mention that I took the filler cap off when it conked out, and bounced the back of the car to make sure I could hear petrol in it (in case my fuel gauge is dodgy) so that would have released a vacuum if there was one.

Fuel pipes in the engine bay are all brand new, so I will double check the tightness of the clips.

I’m wondering now if maybe the mixture was a bit rich, causing it to get too hot when idling, and then with expansion the valves wouldn’t open fully? I don’t know... I’ve leaned off the mixture a 1/4 turn and it’s sat idling on the driveway happily for 20 minutes with the temp gauge sitting nicely at half way so I guess that’s good. Will get out for another drive tomorrow hopefully to see how it runs.

Re: HC Tidy Up (MOT Passed!)

PostPosted: Sat Aug 03, 2019 10:44 pm
by Kraken
Engine bay is looking a it tidier now. New heater hoses and grommet, and a general clean up.



I removed the inner wing liner panel to do some repairs to it. While I was under there I decided to remove the old underseal to see what horrors lay beneath...



A pleasant surprise! Wish I hadn't bothered removing it now, feels like a waste of time. Hey ho, at least I know now. I didn't strip away the very front, as there's a bit of damage to the lower wing, and the front valance has some paint bubbling low down, and I think if I start poking around then things will only get worse. That's a job for later!

On the inside of the wing after scraping away undeseal I found what looks to be 4 spot welds in a row? Any idea why these are here? Arch doesn't look to have been replaced and I can't think of any other reason for them.


Re: HC Tidy Up (MOT Passed!)

PostPosted: Sat Aug 03, 2019 10:46 pm
by Kraken
I'm going to make up new mudflaps, probably using the Demon Tweeks material that Fred has mentioned in the past.

While I'm at it I was thinking of making up some new ones of these mat things that stop muck being thrown off the wheels towards the engine bay (not sure what they're called). Has anybody made any before, and if so, what did you use?